How to change a door to open the other way is an easy task, as long as you have the same height on both sides and agree that the inside face of the door becomes the outside face.

Can I change a door from inswing to outswing?

Yes, it is easy as long as you have enough clearance on opposite sides and the door swing does not interrupt or take up space. The easiest way is to remove the hinges and install them on opposite sides. However, you can remove the casing on both sides and then close the entire outside of the doorjamb, through nails, screws, and shims. If the sill is a freestanding unit or if it has been caulked in place, use the same method with the thinnest sheet possible. If you know ahead of time, do the sill first.

You may need to apply temporary brackets to hold the door in the jamb as the cutting progresses.

You now have a pre-hung door ready to be properly installed on the opposite side of the rough opening after cleaning up that opening a bit. If done carefully, this installation will look like the original.

If there is no clearance or you cannot change the hinges to the opposite side, it is more complex to change and it may be better to replace the door and jamb.

Can I change my front door to open outwards?

The answer is yes, you can change a door to open the other way. Now the procedure is extremely complex, it is not cost-effective because of the investment of money and time and you are better off replacing the door and jamb. Here are some reasons why you should not do it.

You must move the hinges from the inside to the outside, both on the door and on the frame. To do this you must use a chisel and break the hinges.

  • Buy a door latch
  • New jambs
  • Move the striker from the inside to the outside (this is very important because if you don’t change the strikers, you can open the door with a plastic card).
  • Patch the old holes. It is best to remove the frame and put in a new one.

Unless you want to keep the door, it is best to replace it with a pre-locked one and start from scratch.

How do you change a door to swing both ways?

open door

You will need the help of a carpenter to do this activity. The job is difficult in both time and execution. Especially if the door is not symmetrical, if the door is symmetrical it will be easier.

You will need the following materials and tools:

  • 3⁄4-inch sharp chisel.
  • Screwdriver
  • Drill/screwdriver
  • Hammer
  • Crowbar.
  • Pieces of dowel for plugging screw holes.
  • Waterproof wood glue (ANSI/HPVA Type 1).
  • 120-grit sandpaper and thin wood strips to patch jamb notches.

On a sunny day:

Remove the hinges

Leaves go on the same mortises, but you will need to rotate the direction of the mortises so that the hinges are on the inside and reinstall them so that their outer components face outward.

Hold the leaf in place, drill a pilot hole for each screw with a Vix bit, and then drive a screw through each hole in the hinge leaf.

Turn the door over to begin manipulating the hardware

  • The door handle and door latch can be easily removed by unscrewing them. Keep an eye on screws or other small parts.
  • Unscrew the strike plate and turn it around so that the door knob fits backward. Screw it back into place.
  • Screw the knob back into the strike plate.
  • Change the direction of the door sweep with a chisel and hammer. Adding a bead of super glue will help it stick in position.

Use a tape measure

To measure the distance between the top of the frame and the top of the hinge. And transfer those measurements to the opposite side of the door using a pencil.

Using a combination square, make sure the hinge mortises end up at the correct depth on the other side of the doorframe.

Drill the old holes and plug them with dowels and glue

caulking a door

Trim excess dowels and even them out with a chisel, and hammer and sand them smooth. Use the miter saw to achieve the correct depth and size of wood.

Repeat this process for the striker and latch mortises.

Screw the hinges into their new position

  • After re-hanging the door. Using the pins.
  • Take the pencil and color in the striker for the handle and latch. Open and close the door a couple of times to transfer the mark to the door frame.
  • Chisel out the new notches for the handle and deadbolt. Use the drill and Forstner bit to get the hole for the strike plate.
  • Drill and screw the striker plate in the new position.

How to change one door to open the other may be difficult. We recommend you change it from scratch unless the door is an antique and a jewel that you want to keep.

How to change a door to open the other way? was last modified: January 17th, 2023 by Vanessa Gallanti
Your opinion matters, leave a comment
0 Comments
Inline Feedbacks
View all comments