How to remove paint from concrete

Accidents can happen like a paint spill on concrete pavement that stays there or worn paint that is chipping. How to remove paint from concrete is very easy, you just need your safety equipment, patience, and the paint stripper product.

Find out your home's credit score

Check your home condition score to find out!

Check it out

How to remove spray paint from concrete?

Removing spray paint from concrete can be a bit challenging, but here are some methods that may help:

Power washing

Use a pressure washer to blast away the spray paint. Start with the lowest pressure setting and work your way up if needed.

Read more: Cost to pressure wash driveway

Chemical paint stripper

Apply a chemical paint stripper to the affected area, following the instructions on the product. Be sure to wear gloves and eye protection.

Sandblasting

Sandblasting uses high-pressure air and sand to remove the spray paint from the concrete. This method can be very effective but requires special equipment and precautions.

Hot water and detergent

Mix hot water and detergent in a bucket and scrub the affected area with a stiff-bristled brush. Rinse with clean water and repeat as needed.

Baking soda and water

Make a paste of baking soda and water and apply it to the spray paint. Let it sit for several hours before scrubbing it with a brush and rinsing it with clean water.

Before trying any of these methods, it’s always a good idea to test them in a small, inconspicuous area to make sure they don’t damage the concrete.

Does vinegar remove paint from concrete?

Vinegar is not an effective method for removing paint from concrete. While vinegar can be used as a natural cleaning agent, it is not strong enough to break down the chemicals in paint. Removing paint from concrete usually requires a stronger solution, such as a chemical paint stripper or power washing.

Using vinegar on paint stains on concrete may help to loosen the paint slightly, but it will not completely remove the paint. Additionally, using vinegar on concrete may cause damage to the surface if left for too long or used repeatedly. Therefore, it is not recommended to use vinegar to remove paint from concrete.

What is the best product to remove paint from concrete?

The product best ranked by internet sites as the best concrete paint remover is Rust-Oleum. It is capable of removing layers of paint, stain, sealers, and coating on both the exterior and interior. And it is easy to remove because only soap and water are needed to remove it.

How do you remove old paint from concrete?

You will need the following tools and materials to remove the dried paint from the concrete, besides taking the necessary safety measures to protect yourself, gloves, panties, goggles, and a dust mask, after all, it is a chemical that you are handling:

• Broom
• Trisodium phosphate
• Long-handled brush
• Putty knife
• Chemical paint stripper
• Dust mask
• Rubber gloves
• Safety goggles
• Pressure washer
• Kitty litter

Pre-clean the concrete surfaces and allow them to dry

This is essential. You must wash the surface very well before applying the product, in this way, the product will act efficiently and will be able to penetrate and remove the paint efficiently. Sweep or clean the concrete, eliminating leaves, dirt, or dust. Prepare a solution of soap and water or, better yet, diluted trisodium phosphate (TSP); be sure to wear gloves and apply the soap solution or TSP to the concrete employing a long-handled brush. Then rinse the area and allow the surface to dry for one to three hours.

Scrape the chipped areas and apply a paint stripper

If you observe that the paint is chipped, scrape it with a spatula and apply the chemical paint stripper. These products have as the base of removal the same base of which the paint is made. That is to say, depends on the type of paint, and the base paints. If the paint layer to be removed is oil, then you should buy a paint stripper that removes oil. If you do not know, use stripper oil-based paint which is usually the heaviest to remove.

Let the paint stripper layer stand for at least 6 hours. This will produce a chemical reaction and after this time, the paint will be removed.

Remove the chemical residue

You can do this manually or use a pressure washing at 3000psi. If it is done manually, you can do it with a scrub brush or a paint scraper, otherwise, the pressure washer is enough. You will know immediately if you need to reapply the product or not.

We do not recommend other options because they are not as effective, and you may end up damaging the concrete surface to your disadvantage. Sandblasting can crack the area, vinegar is not a good option, and soda blasting paste is not strong enough thinner to remove paint from concrete. Better, buy the right product and follow the instructions, so you don’t overwork it.

Written by Vanessa Gallanti. April 25, 2023

Enthusiast about planning, project management, construction materials and technology, and construction. A civil engineer from Los Andes University and a content writer for Kukun.